Видео

What did you use to polish it at the end? I could not understand what you said.

After you wet sand with the tru oil, do you wipe it down before letting it dry?

I’m not sure I’d take that gun outside. That’s a piece of art.

so you french polish with tru oil instead of Shelac

How long you leave it to dry mate between coats

This is also available in 22 mine make to much noise and shoot not good

Hello My name is Dr. Ricardo Sandoval from El Salvador, Central America. I am looking for Paul Short to buy a Titanium kit for a HW97. Can you provide me the Mr. Short contact? Thank you in advance

No contact at the information given for the moderator, ?

are you dead sir?????

16 joules

I know its 5 years since your video, I have used a similar method but using 'Elbow Grease' de-greaser sprayed on the paper as a lapping lubricant. This deals with any old oil and crud as it arises in the lapping progress. Even better soak it in de-greaser for a day or two before you start lapping to soften up the ground in dirt. Lapping with silicon carbide grits on a granite plate is much faster. btw. If you want some flat granite plates for lapping try your local ornamental stonemason [memorial/gravestone maker], To them, any offcuts or slightly damaged stones are useless scrap and I have had several great ones for free.... always worth a try. My best score to-date was a 3' x 2'6" x 3" rose granite plate that is flat to within a thou with an incorrect inscription on the bottom side - an expensive error on his part .. but a very useful tool in the workshop ! ...... Hope this helps someone ;<)

Steel wool is THE DEVIL. Scotchbrite only.

That piston seal is defiantly not the Weihrauch seal, the one you bought is a design of the original

Great video but the Torque screw is a T8 Dude

Great video how did you flatten you oil stone please

Thanks , trigger reset to a much safer position

Drop some pebbles or marbles into the can to make up for the volume you used, and you'll be able to use the bottle 6 months to 2 years from now without it all plasticizing and turning into goop.

How do you think it’ll go on knife handles

Please do this in a well ventilated room or the Pink Unicorn stood beside you will continue singing "Midnight the Stars and You" ?

Can this kit work work with the Vortek kit?

Would be interesting to see the fp of all 3 ,the last one looks like theres not much effort in cocking it ,is this because its lost power from the tune?

Magnifique, très belle réalisation. Bravo

16 joule

Good job on that. I'm doing a custom stock right now. I got a hairline crack near the bolt and a dent near the fore end I'm getting out. I steamed it and improved it some but now I have to remove the finish to get it the rest of the way

Great video' very helpful

Is 120 grid sand paper considered fine grade sandpaper in your area? I'd call 120 pretty coarse and scratchy.

what was used in the final polishin step?

I live in the Netherlands and have a 21 joules hw97 is it to do with that spring to release the blok by hand and some pressure?

Brake cleaner really removes everything

Still using my metal piston sleave in my 77kse. Vmach lasts 👍

I’ve recently acquired two beautiful air rifles a boxed Walter lgu and last of the Birmingham made air rifles the Wembley longbow both mint con, I’ve put sights on both and had a little plink in the garden and I have to say that the quality and finish on the longbow is beautiful I just cannot put it down.

All my stones have a twin ! I like stones in pairs ! Just rub them together every now and then Like a inca pyramid builder ! Those people knew how to flatten great big stones a that was a ways down the road ! The way you are doing it fine too ! Also if my stone seems clogged up A soak in gasoline or some other light and cheap solvent works for me ! cheerio

Nice video mate👍🏻,What exact wood dye did you put in on if you don’t mind adding the link below👇🏻

Looks great, how much time did you have to wait between coats

Is there anywhere I can get one of those kits? Looked all over...

No difference. Id be disappointed if i paid out for this.

Great Video, it would be better if attach our night vision scope camera on...😀

Great video. Tip: Use a rubber band or hair tie to your applicator so you don't have to wrestle with holding the material together to stop the filling coming out.

Waste of money by the sound of it , but a very good video informing the public of not to waste money on , thankyou .

I used your exact method on a lap steel guitar I made. It turned out fantastic! THANKS! ruclips.net/video/_4wT47G_hi0/видео.htmlsi=ARql0r2F64KfKuie

30mm preload?, curse of HC version, only about 6mm on my mk1 full length.

Is blacking and blueing the same thing? I’m just starting a very early mk1 hw80 and I’m planning on doing exactly what you have

What make and where can I get the suppressor for the HW97 please..

Gorgeous ❤ Thank you for your help

I have trouble in trigger assembly when I load the gun safety of gun is fired without touching the trigger blade of my airarms prosport please let me know where is the problem after adjusting first and second stage same position as before adjusting

I have trouble in trigger assembly when I load the gun safety of gun is fired without touching the trigger blade of my airarms prosport please let me know where is the problem after adjusting first and second stage same position as before adjusting

I’m looking at sending my 97 to Paul but a bit worried about the shot cycle as have never shot a fast one

I’ve watched all of your RUclips videos on air rifles and shooting and sharpening tutorials and as I do a bit of both have found you a very good te@cher , so very much obliged

Where is the speed measurement with the chronograph, where is the target with the results? It is not a good and educational video, so anyone can make a video on YT and claim that their project has succeeded.

thank you for showing us how your rifles coming along ,Have you a link please for paul short pistons and how much does it cost please for the upgrade ,and the seal from Ausy ,thanks .